OLD Technical Questions

New Seawych Messageboard
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Boom Fitting

Post by webmasterphbb1 »

Boom Fitting
Post by glynwilliams » Fri May 03, 2019 10:28 am

Help please,
I have just launched my boat "Wychway To", and it was rigged in my absence.

Forgive the non technical language
the slot on the boom, takes the main, is offset by 20/30 degrees from
what I thought should be vertical, how do I adjust this.
It reminds me of the boom arrangement on my old Foxcub but I
had a key to turn the boom, do I need a key?
I have just got the sails back after having new UV strips
fitted and I dont want to look a complete ------ when I fit the sails.
This is the voice of ignorance calling
regards
Glyn
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Boom Fitting
Post by Vic » Fri May 03, 2019 4:49 pm

If you have the original boom with Barton roller reefing then you can rotate the boom using a Barton reefing handle until the slot is on the top

If your boat has been converted to slab reefing and you do not have the reefing handle and do not require one it will be simple enough to improvise something to do the necessary unless the gear has been neglected and seized up.
Pictures below ( I hope ) shows the Barton reefing gear and where the handle fits to rotate it. Also the handle itself (Currently about £40 to buy)

If you do not have slab reefing and will therefore the using the original roller system then you will need the proper handle or a decent substitute

I recommend a slab reefing system although I also keep my roller system in working order

Image

Image
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
glynwilliams
Posts: 11
Joined: Sat Mar 23, 2019 8:20 pm
Re: Boom Fitting
Post by glynwilliams » Fri May 03, 2019 5:55 pm

Hello,
thank you Vic,
I shall peer into the hole and try and
improvise something to move the boom as slab reefing
is my ideal but as you suggested I will try and renovate and
keep the roller system in working order.
The fitting appears to be triangular.
There will be more questions I am sure
regards
Glyn
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Boom Fitting
Post by Vic » Fri May 03, 2019 8:42 pm

The fitting appears to be triangular.
No it is square ...... from memory 1/4" or 5/16"
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
glynwilliams
Posts: 11
Joined: Sat Mar 23, 2019 8:20 pm
Re: Boom Fitting
Post by glynwilliams » Sat May 04, 2019 6:50 am

Thanks again ,
The sun is shining ,so off to the Marina
I will report back
Regards
Glyn
Wychway To
Top
glynwilliams
Posts: 11
Joined: Sat Mar 23, 2019 8:20 pm
Re: Boom Fitting
Post by glynwilliams » Sun May 05, 2019 3:41 pm

Hello Vic

well done and thank you for your help.
I used an appropriate sized screwdriver and hey presto
the boom revolves as needed.
I wonder why the Barton system fell out of favour, does
it have problems with the battens?
I think in some ways it might have suited me,being of senior
status and not as mobile as I once was.
When you have the time can you steer me in the direction of
the pros and cons?
regards
Glyn
"Whychway To"
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Boom Fitting
Post by Vic » Mon May 06, 2019 9:05 am

The troubles with the roller reefing system are:
As you roll the sail the thickness builds up at the forward end of the boom with the result that the aft end droops lower and lower
You cannot tension the new foot of the sail
You cannot use a fixed kicking strap. Instead you have to use a claw ring arrangement which is poor by comparison and which has to be guyed to the mainsheet fitting on the boom end, which bends!

The result is baggy sail which cannot be flattened in the very conditions in which you need to be flattening the sail.

A slab reefing system does not suffer from boom droop, allows the new foot to be properly tensioned and allows the use of a good kicking strap attached directly to the boom. the result is a far better shaped and flatter sail more appropriate to the conditions
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
glynwilliams
Posts: 11
Joined: Sat Mar 23, 2019 8:20 pm
Re: Boom Fitting
Post by glynwilliams » Mon May 06, 2019 2:38 pm

Many thanks for all your help
,as you have suggested I
will stick to slab reefing
regards
Glyn
Wychway To
Top
8 posts • Page 1 of 1
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Transducers

Post by webmasterphbb1 »

Re: Transducers
Post by hughfairbrother » Sat Mar 23, 2019 2:04 pm

Hi Glyn,

Welcome to the Wyches. My transducer was fitted by the original owner about 12 inches behind the toilet thro hull. Not sure if that's correct but seems to do the job.

Any pics of your new purchase?

Also are you aware of the Facebook page for Seawych Owners?

Cheers
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Transducers
Post by Vic » Sat Mar 23, 2019 4:25 pm

My echosounder transducer is behind where the loo was ( ie at the forward end of the toilet well)

Image

I have a towed log but if fitting a transducer follow the guidance of the manufacturer, I'd probably fit one in the under-sink cupboard on the opposite side to the sink drain ... but it would restrict access to the area under the cockpit sole.

Unless you actually want a continuous indication of of speed through the water ... eg to aid sail trim when racing, don't bother fitting one.
For navigational purposes a GPS is a better choice.
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
glynwilliams
Posts: 11
Joined: Sat Mar 23, 2019 8:20 pm
Re: Transducers
Post by glynwilliams » Sat Mar 23, 2019 8:23 pm

Hello,
I will send some pics later this week,I just fell for her looks
thanks for the reply
Glyn
Top
hughfairbrother
Posts: 5
Joined: Sat May 19, 2018 10:21 am
Re: Transducers
Post by hughfairbrother » Sun Mar 24, 2019 10:03 pm

Super look forward to seeing her.
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Mast Support Beam

Post by webmasterphbb1 »

Mast support beam
Post by paulgemmell » Mon Mar 04, 2019 1:35 pm

Hi All,
The interior roof on Sable is sagging, reading through some posts suggests that the beam might be rotting. As this is going to be quite a big job I'd appreciate an advice or images from what to expect when removing the foam on the cabin ceiling. An image can be viewed via this link.

https://4385002.tifmember.com/v/photos/ ... 04/mg-8504

It's not very clear in the image but there is a definite sag. I'm hoping the beam is sound and it's only the foam that's come away from the fibreglass where it has cracked, although there is a definite dip on the exterior side of the coachroof.
Any comments would be much appreciated.
Many thanks,
Paul
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Mast support beam
Post by Vic » Mon Mar 04, 2019 3:11 pm

Its difficult o tell. Mine has always, even from new, looked as though the mast beam was sagging from the inside.

Any deformation on the outside especially any cracks in the gel coat would be a sure sign that the beam has rotted or is broken and is sagging.

Usually i think people tackle the beam replacement from inside although one person, I'm sure reported on here somewhere, cut the moulding away on the outside, refitting it again when the new beam had been fitted.
Also some record of fitting a compression post internally.

Replacing the beam however you do it is an unenviable task!


One thread I found but which you may already have seen viewtopic.php?f=4&t=365
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
paulgemmell
Posts: 13
Joined: Mon Nov 28, 2016 8:27 pm
Re: Mast support beam
Post by paulgemmell » Mon Mar 04, 2019 3:35 pm

Hi Vic,
Thank you for your prompt reply.
I'm going to cut out the foam and fibreglass and replace. This section of the interior coach room has a crack in it. I'm hoping this is in part due to the amount of holes that have been drilled in this area.
I will post any images I take.
Regards,
Paul
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Bow and transom corners and mast beam

Post by webmasterphbb1 »

Bow and transom corners and mast beam
Post by maxholt » Mon Nov 25, 2013 3:02 pm

We have recently acquired Sunrise Seawych number 103 (or at least that's the number on our sail) She had the rubbing strake replaced with a wooden box affair that has rotted away. Now we want to replace the rubbing strake with something very near to the original. On looking at other Seawyches, there appears to be stainless steel corner pieces round the transom and the bow. Can anyone help out with a pattern or drawing of these so I can fabricate some? I would like to keep them as near original as possible but as always with these things it might not be possible to get them exactly the same.

Also we have the usual mast support beam problems. I have drilled into it and it seems to be dry and not rotten. However, the inside skin in the roof has a distinct sag, and the outside gel-coat is badly cracked down each side of the mast support block. A failed attempt at sealing it up with some sort of gunge has been made, (not by me!). So We are cutting out the beam and replacing it with a tight fitting, hard wood beam, bonded into its housing with epoxy and re fiberglassed up.

Also I am hoping to seal up the inside of the chain locker and make a drain hole for it, a water tight access hole inside the boat as well.

Other things in the pipeline are Plexiglas bolt on windows, fiberglass locker tops, replacing the running rigging and kicking strap.
If anyone out there can help with any of this we would like to here from you.
Max, Joe and Pippa.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Bow and transom corners and mast beam
Post by Vic » Mon Nov 25, 2013 10:32 pm

Hi Max

The original grey PVC fendering is no longer available. Not even sure if the section is still available in black.

Wilks were/are the source of such mouldings http://www.wilks.co.uk/marine.aspx The original was their section PVC 17/70

The last i knew was that they could still manufacture to a special order but the minimum quantity was quite considerable. ( 150m ???)

Take a look at the website.. I reckon you'll find something that will do the trick. Not cheap though!

Dunno who made the bow and corner plates... Sadler supplied them. Suggest you look at some on another boat draw what you want and get a local stainless steel fabricator to make them or make them yourself. I reckon you could improve on the originals anyway so don't faff about trying to get/make exact copies . Might need to be slightly different anyway to suit whatever fendering you use

IIRC there is info in the Owners Manual on replacing the mast beam. Download a copy if you have not already done so.

A few people have fitted a compression post ... not for me though! Maybe some photos in a past post on here if not i have some if you are interested.

Personally I'd not bother altering the chain locker. I think you will end up with it very shallow if you raise it so that it drains over board and does not flood with every wave. I flake the chain on deck briefly to drain before stowing. I live with the small quantity of water that does find its way into the forward under berth lockers. I do have a removeable panel that closes off the top part of the locker... just so that it looks nice from inside.

Bolt on windows probably a nice idea but nicer if the openings had been cut smaller originally so that the windows could remain the original size. Drill screw holes a little oversize or thermal expansion will cause cracks around the bolts... don't use countersunk fixings or cracks will occur. Many people find butyl tape good for bedding new windows on.
Personally fitted new ( acrylic) widows in rubber mouldings like the originals.

BTW it maybe worth getting the forward windows "drape moulded" to the shape of the old ones so they fit the curved of the cabin sides easily.

Polycarbonate or Acrylic ( Perspex, Plexiglass ) your choice. Polycarbonate scratches more easily I believe and is more susceptible to damage by solvents otherwise virtually unbreakable.

GRP locker tops available from the Sea Wych shop........ need to think about suitable hinges though.

Convert to slab reefing if not already done. Much better sail shape when reefed and you can fit a decent kicker


Vic
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Fri Dec 13, 2013 10:11 pm

Thank you for your input Vic, much appreciated. I have checked out most of the mast support beam comments and recommendations and have decided to replace the beam and the step block with a shaped hardwood replacement. Like you, I am not in favor of the compression support as I am no spring chicken at 20 stone +. I thought about tackling it from inside, but now considering cutting it out from outside and digging the old wood out of the fiberglass exterior box, making the new beam fit into it. This has its advantages in so far as I wouldn't have to tackle fiber-glassing the beam back into place from inside the boat.... Messy and subject to gravity so it would involve some sort of support to hold it in place whilst it set. The cosmetic wounds on the outside would be filled with gelcoat filler after replacing, then flatten off with wet and dry. Our intention is to paint the top and bottom with FlowCoat epoxy paint, giving a tough gelcoat like finish, white for the top and tangerine for the bottom. The windows will be 3mm plexi-glass with a 2mm overlay marine-ply frame and bolted on. I intend to dig out the foam from between the two layers of fiberglass round the window and insert some hard wood to form a stronger medium to tighten the windows down to. I will be using a suitable silicon based sealer like transparent sikaflex or similar to seal them. The chain locker has a cupboard type door on the inside that, not only looks bad but also fails to stop any water washing down the chain-pipe from soaking the cushion in the forepeek. This is obviously going and being replaced with a water tight locker door. Thus the need to seal off the bottom of the chain locker from the bilges and drill a hole through the side of the boat from inside to drain it. I wouldn't particularly matter if water got in through it as it would be above the waterline anyway and drain naturally. On the up side, it would help flush out any sand and sediment going down the chain pipe.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Bow and transom corners and mast beam
Post by Vic » Sat Dec 14, 2013 5:08 pm

I dont think I would tackle the mast beam from outside. At least not unless the grp is already very badly damaged.

I know its an unpleasant job to do from the inside but there is only a thin inner skin of fibreglass to cut a way to access it. A new beam wont be difficult to prop into position while the resin sets.
The outer mounding is part of the main structure and restoring that to the original strength etc will be a fairly major job without even thinking about the cosmetics involved.

3 mm acrylic is, IMO, too thin for the windows. The originals were 5 mm. Using polycarbonate might be better from the strength point of view is you must use 3mm but I think it will still be too flexible. I saw someone trying to use some thin stuff ( no idea if it was acrylic or polycarbonate ) for some windows in a similar sized boat a few years ago. It was unsatisfactory.
There is no foam around the windows unless someone has made some modification. The cabin sides are just a single thickness GRP moulding approx 5mm thick.

It sounds as though someone has tried to be clever by fitting a door in the chain locker bulk head. Mine is as original, and coated on the chain side with resin and glass as recommended in the building instructions. I have added a removable panel above it to close off the few inches normally left open between it and the deck for purely aesthetic reasons.

I have no problems with water going down the chain pipe but I don't generally sail with the bows under water! However if you successfully make a self draining locker then I look forward to reading about it in the magazine.
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Mon Mar 03, 2014 10:05 pm

Thanks for your words of wisdom Vic! Cut the inside section out.... It was extremely difficult! And not a single, thin layer as you said, but 2 thick layers and a sandwich of foam between to boot. The wood inside was very wet and had little mast support strength. The first piece came out quite easily but the second was virtually impossible to get out without damaging the top layers of fiberglass further. At this point I went back to plan A and carefully cut the support beam box off at 1/4" above the deck. This removed I still found it difficult to remove the rest of the wood but managed it by screwing some large screws onto the it and levering it out against a pivot spreading the whole effort across the upturned box. Once out I removed most of the packing fiberglass that I supposed was the majority of strength in the mast support as the wood only seems to be there to fill the gap. I have ordered a solid beam made from a Mahogany type hardwood. Hopefully when it comes I'll set it into the box and pack it well with chopped mat and resin. Ill seal up the hole in the roof, again from outside (shuttering it up inside) And hopefully when I put the beam, in its box back into place it should fit pretty much in it's original position. It may need a bit of trimming up but I think I can fill any inadequacies with gelcoat filler. This done, and sandblaster been and gone we can then tackle the paint.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Bow and transom corners and mast beam
Post by Vic » Wed Mar 05, 2014 6:35 pm

Thats for the feed back.

Id forgotten the foam.
When I have cut into the inner skin it has been fairly thin and I had not realised that there was another skin above the foam buts logical that the beam would have been glassed over after being fitted suppose.

Did you Take any pictures. I am sure a brief illustrated account of what you've done would be welcome copy for the magazine, esp having tackled it in a different way
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Fri Mar 07, 2014 11:19 pm

No pictures yet but I will be taking some as I go through the reassembling process. Watch this space. :)
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Tue Mar 11, 2014 11:32 pm

Some pictures of work in progress:
More pictures to follow as work progresses. Hopefully of better quality than these as I am between cameras at the moment.
ATTACHMENTS
Mast beam replaced and left to set..jpg
Mast beam replaced and left to set..jpg (156.88 KiB) Viewed 417 times
Mast beam in place ready to be glassed up and seald into its box..jpg
Mast beam in place ready to be glassed up and seald into its box..jpg (176.58 KiB) Viewed 417 times
mast beam in place and seald into its box..jpg
mast beam in place and seald into its box..jpg (206.56 KiB) Viewed 417 times
Last edited by maxholt on Sat Apr 19, 2014 9:36 pm, edited 1 time in total.
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Sat Apr 19, 2014 10:49 am

More updates to our mast beam replacement and some follow up pictures.
Also the work in progress on the chain locker.So far we have removed the door and hinges that was originally in place and left the board it was attached to in place. This, together with the original door didn't extend to the underside of the deck, so we have cut a new piece of marine ply to partition off the chain locker completely. we have fitted a round watertight access hatch cover to the new partition. The floor of the chain locker has now been cut and fits perfectly in the bottom of the locker, I have secured an eye bolt to it with a D shackle to attach the anchor chain to with a stainless plate underneath. I have riveted over the threads after tightening the nut up to prevent it from coming unscrewed once it is fiberglassed into place.
ATTACHMENTS
Chain locker floor sized 2 .jpg
Chain locker floor sized 2 .jpg (161.57 KiB) Viewed 417 times
Chain locker pertition showing round hatch.jpg
Chain locker pertition showing round hatch.jpg (184.47 KiB) Viewed 417 times
Chain locker pertition with shelf backing and door remouved.jpg
Chain locker pertition with shelf backing and door remouved.jpg (143.86 KiB) Viewed 417 times
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Sat Apr 19, 2014 9:40 pm

I've edited the original pictures and posted some resized ones. Makes them easier to view.
Top
maxholt
Re: Bow and transom corners and mast beam
Post by maxholt » Thu May 28, 2015 8:34 pm

UPDATE
It has been a while since I have done anything with SUNRISE now, and things have been sloping down the slippery slope to complete lack of interest. So! we decided to get her under cover at all cost and arranged to take her to a boat yard in Wales where we could go down for 6 days a month and complete the work over the next 3 months. Yes! Your absolutely right. We are dreaming. So as we are in a dilemma with cover staff for our disabled employer and proper transport we have now had to scrap that idea. Just as well coz we have now been offered a building locally at an affordable rent that if it will go in we can do all the work whenever we have an od day or even half a day to spare. the osmosis is looking very tedious but we think we can get to grips with it when she dries out. we have the paint, fittings and filler to get on with it now so we have no excuse.
More posts to come in the near future....... Still no corner bits! Anyone know of any going anywhere?
Top
paulgemmell
Posts: 13
Joined: Mon Nov 28, 2016 8:27 pm
Re: Bow and transom corners and mast beam
Post by paulgemmell » Mon Feb 11, 2019 8:51 am

Hi,
This seem like a job I need to tackle, just wondering if you still have any of the images available.
Many thanks,
Paul
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Hole left by toilet removal

Post by webmasterphbb1 »

Hole left by toilet removal
Post by hughfairbrother » Mon Jan 07, 2019 12:23 am

I have recently removed the toilet leaving a large hole. Has anyone got an easy fix or do I need to do a standard fiberglass 1 in 12 thickness chamfer solution?
Vic, have you repaired yours yet and if so what did you Do?
Many thanks
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Hole left by toilet removal
Post by Vic » Sat Jan 12, 2019 11:21 am

Hi Hugh

Sorry not to have replied sooner

Yes I repaired the hole left by the toilet.

I opted to do a standard chamfered repair from the outside, although my chamfer was somewhat less than the 12:1 recommended

I repaired from the outside because I thought that a patch on the inside would have been potentially weak at a point where the yard was likely to jack-up the boat when loading/ unloading the launching trolley. I did however also put a couple of layers of glass cloth over the entire area on the inside.

I bought a compact 115 mm angle grinder that could be used with one hand within the confined space of the toilet compartment and a rubber sanding backing pad accessory. ( i found that sanding was an adequate way of preparing the chamfer etc and easier for a novice to control rather than a more aggressive grinding disc.)

https://www.silverlinetools.com/en-GB/P ... ame=571295

It was quite difficult to judge an even chamfer, especially on a curved surface

I used West epoxy resin and 600g bi-axial cloth. Epoxy because the bond with the GRP would be stronger than with polyester resin and not require gel coating to make fully water resistant. 600g cloth because I judged that to be a good compromise between a smaller number of thicker layers and a larger number of thinner layers. ( but see later comment)

Having prepared the chamfer and the inside surface I started the repair with two layers on the inside with peel ply ( to give a suitable bloom free surface for the outside layers to adhere to ) backed up with a piece of heavy gauge polythene and a stiffish foam backing pad ( ex packaging material) all held in place on the outside with gaffer tape.

I prepared a one piece patch for the outside from the appropriate number of circles of cloth, with the largest equal to the diameter of the prepared area and the smallest the size of the hole, rather than applying the layers one by one. ( Note the largest circle is the first one in contact with the hull, the smallest the final one working outwards)

I found it difficult to accurately position the prepared patch. Another time I would mark up some better guide lines

I recommend studying as much info as you can find on the West system websites
https://www.westsystem.com/instruction-manuals/

and viewing the appropriate videos
https://www.youtube.com/playlist?list=P ... AT6ciaY3hB

I bought all my materials from East Coast Fibreglass Supplies although I have also used CFS

I bought:
1 metre of 600g bi-axial cloth ( Loads more than I needed, but its cheap enough. Thinner would mean more layers and therefore use a bigger proportion)

a 1.2kg pack of West Epoxy resin. A 600g pack would have been enough but I did not want to run out part way through)

A tub of colloidal silica and a tub of low density filler

a pot of signal red pigment ( a decent match with the red hull)

A metre of peel ply ( already explained)

Also
A mixing kit, 2 each 1" and 2" brushes, a finned roller ( because I'd lost mine), dispensing pumps to fit the 1.2kg pack ( accurate measuring is important when using epoxy) and a can of acetone

Total spend in 2013 incl shipping and VAT : £110

I have loads of cloth, peel ply and fillers left over, quite a bit of resin and most of the pigment
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
hughfairbrother
Posts: 5
Joined: Sat May 19, 2018 10:21 am
Re: Hole left by toilet removal
Post by hughfairbrother » Sun Jan 13, 2019 1:52 pm

Many thanks Vic for the detailed response. I think I now feel a lot braver to carry out the work 😉
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

'Skeg' Plate on Seawych Stern

Post by webmasterphbb1 »

'Skeg' Plate on Seawych Stern
Post by kirstiehowell » Thu Jan 10, 2019 1:09 pm

Hi there, I was wondering if anyone could help. I have a sadler 19 and a chap on my pontoon was telling me about a 'skeg' plate that could be fitted to the aft of the boat which helps with stability whislt sailing. Has anyone modified their boat this way?
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: 'Skeg' Plate on Seawych Stern
Post by Vic » Sat Jan 12, 2019 11:56 am

First point to make is that the Sea Wych was designed by J.V (John) Sadler and built mostly by his company Sadler and Sons.
The Sadler range of yachts were designed by David Sadler and built by Sadler Yachts, IIRC David Sadler's son, Martin's, company.

There is no connection between John Sadler and David Sadler or Sadler Yachts or between the Sea Wych and the Sadler range of yachts

John sadler always claimed that he had tried a skeg but that it made no useful improvement, merely making it difficult to load/ unload the boat onto a trailer. I suspect the latter was the main objection!

The only Seawych I have seen with a skeg is Peter Bates'. Perhaps if he sees your question he will explain his reasons for fitting the skeg and provide some details.

just visible behind Peter in this picture ( not helpful but another opportunity to post the picture)

Image
Vic
Brave Dragon

Visit the Yatching and Boating World forums
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Sail Repairs/Replacement.

Post by webmasterphbb1 »

Sail Repairs/Replacement.
Post by rogerdurham » Fri Jun 16, 2017 2:01 pm

Hello all, I'm new to association and to owning a seawych having recently purchased 'Trunkles' in a very poor state.
I'm currently in the process of bringing her up to a sailing standard internally and externally and will require lots of help, advice and suggestions.
The first of which is below:
The Jib sail is on the original reef roller and seems in serviceable condition, although the Blue Strip surrounding the sail is in very poor condition suffering what seems to be extensive UV damage (bleaching and material degradation). Is this a sign that I should replace the entire sail or could it be saved?
Could anyone suggest a appropriate replacement or a company that could possibly repair the original sail.
Many Thanks.
Roger.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Sail Repairs/Replacement.
Post by Vic » Fri Jun 16, 2017 7:21 pm

Welcome to the Association.


The blue strip is sacrificial. Its purpose is to protect the sail itself from UV damage.
Provided the sail is in good condition the UV strip can be replaced as/ when necessary.

I don't know where you are but any sail maker and many cover makers will do it. It' s a routine job for them.

It's not cheap though . The cover makers where I take mine charge £80.00 + £17.00/m of leech length. eg for an 6m leech would cost £80.00 + (£17.00 X 6 = £102)= £182.00 (the price includes the foot).

However you may be able to negotiate a reduction if you remove the old strip yourself as it is half the job. Be warned though that if the sail is dirty they may well want to have it laundered first.
Last edited by Vic on Wed Sep 06, 2017 1:14 pm, edited 1 time in total.
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
rogerdurham
Re: Sail Repairs/Replacement.
Post by rogerdurham » Fri Jun 16, 2017 8:46 pm

Thanks Vic :), I have feeling I'm going to be on here quite frequently asking many questions. :lol:
By the looks of it the Sail hasn't been off the reef roller for a very very long time as the extremity has bleached to almost white from the original blue.
What's been rolled up isn't too bad but their are strips coming away on the most exposed areas.
The main however has been kept in sail bag stowed in the cabin and is in great condition.
I have many many things to do on the boat to make her presentable and sail worthy again. It seems from the state of everything on the deck and the mast shes been languishing in a boat yard under a tree for a year or two. Much of the running gear and tackle is missing as are the lines and halyards, what is present is green and probably beyond any serviceable use. And that's just whats been on the deck!
I'm in north Lincs/ Notts area. (Around Lincoln/ Worksop area).
I should imagine that the cost of renewing the UV strip is far less than a new sail?
Know of any companies in my area that could handle the job?
Thanks.
Roger.
Top
brianbowman
Posts: 2
Joined: Sun Aug 05, 2018 7:31 pm
Re: Sail Repairs/Replacement.
Post by brianbowman » Sat Aug 18, 2018 7:10 am

Hi all I’m also a new owner of a seawych and I also got mine in a very poor state but could see the potential straight away. Sadly mine came with no sails and was wondering if I could pick second hand ones up or any sails that might fit thanks for reading
Top
hughfairbrother
Posts: 5
Joined: Sat May 19, 2018 10:21 am
Re: Sail Repairs/Replacement.
Post by hughfairbrother » Mon Aug 27, 2018 4:32 pm

Hi Brian,
They come up for sail from time to time on eBay. There was also a set for sale on this forum a month or 2 ago. Guess best to keep looking. I also read their was another type of boat with similar sails that could be used but sorry can't remember the name. Cheers and good luck !
Top
brianbowman
Posts: 2
Joined: Sun Aug 05, 2018 7:31 pm
Re: Sail Repairs/Replacement.
Post by brianbowman » Mon Aug 27, 2018 5:28 pm

Thanks for reply I was told enterprise dinghy sails might fit what do you think
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Sail Repairs/Replacement.
Post by Vic » Mon Aug 27, 2018 11:01 pm

ITYWF that the Enterprise mainsail is a little smaller than the Sea Wych main but because the Enterprise is fractionally rigged the jib is very much smaller.
The total sail area is only 10.5 m²
The Enterprise sails may well be made of lighter weight fabric.
Vic
Brave Dragon

Visit the Yatching and Boating World forums
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Bilge Keels

Post by webmasterphbb1 »

bilge keels
Post by paulgemmell » Thu Apr 05, 2018 6:29 pm

Hi,
Just wondering if anyone has had any issues with fibreglass above the bilge keels (please see photos-first 3 images)

https://4385002.tifmember.com/v/photos/69962hrm/sable11

I'm not sure but it seems there might have been water dripping from electrical wiring which has resulted in the glass sinking into the bilge keels.
Seems quite serious though.
The images are not that clear but it's quite dark down there.
Thanks in advance.
Cheers,
Paul
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: bilge keels
Post by Vic » Thu Apr 05, 2018 9:06 pm

The void above the ballast in the keels should have been filled with 2 part, self expanding, foam and the top glassed over with resin and CSM.

I'd be very puzzled if I saw anything like than in my boat
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
paulgemmell
Posts: 13
Joined: Mon Nov 28, 2016 8:27 pm
Re: bilge keels
Post by paulgemmell » Fri Apr 06, 2018 9:53 am

Hi Vic,
Thanks for your prompt reply.
It's reassuring to know that there is a void above the ballast, looks like I'm going to have to remove the the glass sheets and have a look inside the keels.
The battery compartment was situated there and wonder if a leaking battery might have caused the issue.
I'll post some photos when I get round to removing the glass sheets.
Many Thanks,
Paul
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Locker Tops

Post by webmasterphbb1 »

Locker tops
Post by stevehowlett » Tue Jun 27, 2017 8:11 pm

Hi all, recently purchased a set of locker tops.

My newly acquired Seawych 'Bogi' has currently some seriously delaminated wooden ones that are several seasons well past saving.

Got the instructions that go with them, but they're slightly bewildering to me, as there's no mention of sizes of hinges and hardware that I'd need to fit them.

Does anybody have any information they could kindly share with me please? Or any tips found whilst fitting your own? Or even some close-up images of them installed.

Thanks.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Locker tops
Post by Vic » Tue Jun 27, 2017 9:01 pm

Personally made new wooden locker tops

But you might find this previous thread helpful .

viewtopic.php?f=4&t=151&p=484&hilit=locker+tops#p484
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
stevehowlett
Re: Locker tops
Post by stevehowlett » Wed Jun 28, 2017 5:51 am

Thanks Vic,

That could well prove to be helpful.
Top
paulaston
Posts: 20
Joined: Wed Jun 29, 2016 8:28 pm
Re: Locker tops
Post by paulaston » Thu Mar 22, 2018 7:12 am

I also have a set of locker tops from the SeaWych shop and I am struggling to work out how to fit them.

I am hoping to keep this as simple as I can by permanently fixing the vertical sections rather than fibreglassing them to the horizontal locker tops.

But I still need to get a suitable set of hinges for the locker tops.

The photos on the previous thread are not visible unfortunately, so I’d appreciate any photos anyone might have or any specification for hinges or supplier details please.

Thanks

Paul.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Locker tops
Post by Vic » Thu Mar 22, 2018 2:45 pm

I would not fix the locker top fronts in place. If only the top opens the access to the lockers will be so restricted that they will be next to useless.

If you glass battens to the undersides of the tops and the insides of the fronts you will be able to hinge them together with ordinary butt hinges in a similar way to my plywood locker tops

Image

To hinge the tops to the cockpit coaming I found some hinges similar to these Westerly spares ,only fitted the opposite way up to the picture. They were very expensive!

http://www.westerly-yachts.co.uk/popup_ ... hp?pID=458
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
paulaston
Posts: 20
Joined: Wed Jun 29, 2016 8:28 pm
Re: Locker tops
Post by paulaston » Thu Mar 22, 2018 8:04 pm

Thanks Vic
Top
paulaston
Posts: 20
Joined: Wed Jun 29, 2016 8:28 pm
Re: Locker tops
Post by paulaston » Mon Mar 26, 2018 10:04 pm

I took the old locker tops off today and tried to place the new grp locker tops supplied by the SeaWych shop last year into position to work out if the hinges I’ve found will do the trick or to see if I need some different ones.

Unfortunately I didn’t get that far because the locker tops and fronts do not fit. The fronts could possibly be fettled and trimmed to make them go somewhere close (although my expectation is that I should not have to do that). However, there is no way the locker tops will straddle the locker opening and the locker front as it is indicated that they should in the supplied drawings; and no amount of fettling or trimming is likely to solve that.

Can anyone help me answer the following questions please so I can try to work out what the problem is and decide what to do next?

1. Do all Sadler SeaWych 19s have exactly the same size locker openings?
2. Who manufactures the locker tops and what are their contact details?
3. Has anyone got any technical drawings with exact dimensions for the supplied locker tops and fronts so I can check those dimensions against the ones I have been supplied with and against the locker openings?
4. Has anyone successfully fitted the same locker tops and fronts to their Sadler SeaWych 19?
5. Has anyone got any pictures please of successfully fitted locker tops and fronts?
6. Has anyone had a similar problem fitting these as I have and if so how did you solve it?

Thanks in anticipation.

Regards,

Paul.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Re: Locker tops
Post by Vic » Tue Mar 27, 2018 7:00 am

I know a certain amount of fettling is necessary but they should fit !

Peter Bates ( Southern area rep) was fitting some last year, but due to ill health I have not seen the finished result.

In case of real problems with them contact Jean and Dave Bannister. They get the tops made, but I do not know by whom.
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
paulgemmell
Posts: 13
Joined: Mon Nov 28, 2016 8:27 pm
Re: Locker tops
Post by paulgemmell » Thu Mar 29, 2018 3:37 pm

Hi Steve,
Hinges on Sable are from Seasure-https://www.sea-sure.co.uk/products-sku?populate=hinges
Some images of how the hinges are fitted can be viewed here-https://4385002.tifmember.com/v/photos/69962hrm/sable11
Cheers,
Paul
webmasterphbb1
Site Admin
Posts: 57
Joined: Tue Jun 30, 2020 6:40 pm

Fitting GRP Licker lids...Help req'd

Post by webmasterphbb1 »

Fitting GRP Licker lids...Help req'd
Post by Vic » Sun Jun 04, 2006 10:26 am

I have had a query from a member who does not have internet access about fitting the grp locker lids.

As I have not fitted these to my boat I was unable to help.

Would a few others like to tell me how theirs are fitted. What sort of hinges have been used etc, where on the boat are the hinges fixed and is it necessary to reduce the depth of the rear lip so that they can be hinged.

A photo or two would be nice
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
Colin & Karen Leonard
Post by Colin & Karen Leonard » Sun Jun 04, 2006 7:47 pm

Hi Vic,

We have attached a picture showing the hinges on our locker tops (not an area where you naturally take any pictures particularly inside),
We didnt fit them ourselves and have never had much need to pay any particular attention to them. The fronts are hinged internally to the tops and these hinges (if my memory serves me correctly) have been fibre glassed in place.
I do not know what they are like when they are new but they can catch on the back when opening so may need some minor adjustments to the height on the side that hinges to the boat.
They are fitted with a hasp and staple for securing in a closed position.
If necessary we will take some more pictures next weekend if no-one has any.

Colin & Karen

Image[/img]
Last edited by Colin & Karen Leonard on Sun Jun 11, 2006 6:27 pm, edited 1 time in total.
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Post by Vic » Mon Jun 05, 2006 12:03 pm

Thanks for that. I will print it out and send it on. It sounds as though the back lip has to be trimmed. Then it is a question of finding suitable hinges. For my wooden tops I found some (very expensive) aluminium hinges in chandlers intended for lockers or hatches.

Other answers eagerly awaited.
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
Colin & Karen Leonard
Post by Colin & Karen Leonard » Sun Jun 11, 2006 6:20 pm

Vic,
Attached are some more photos which I hope will be of assistance, I did not fit the locker tops myself but they seen to work OK.
You will note that the side that is hinged to the boat has been cut away, it seems as though without this they will not open and if the cut away is not deep enough they rub on opening.
As mentioned previously the internal hinges are fitted in place with fibre glass also it appears the a small shim if ply has been used to get the correct spacing (I didn't have anything to measure it but I would say approximately 4mm ply was used).
I am not sure why the tape has been put on, maybe to reduce sticking where they are a snug fit at the back.

I hope this helps.

Colin & Karen.

Image

Image

Image

Image

Image

Image

Image

Image[/img]
Top
Vic
Posts: 618
Joined: Mon Feb 28, 2005 9:51 pm
Location: Home: Kent, Boat:Solent
Post by Vic » Sun Jun 11, 2006 11:08 pm

Thanks I have printed that out and will send it on. I am suggesting that an article on fitting the lids would be a useful contribution to the Owners Manual but I have not heard anything since I sent the last picture etc
Vic
Brave Dragon

Visit the Yatching and Boating World forums
Top
paulaston
Posts: 20
Joined: Wed Jun 29, 2016 8:28 pm
Re: Fitting GRP Licker lids...Help req'd
Post by paulaston » Thu Mar 22, 2018 7:11 am

I have a set of locker tops from the SeaWych shop and I am struggling to work out how to fit them.

I am hoping to keep this as simple as I can by permanently fixing the vertical sections rather than fibreglassing them to the horizontal locker tops.

But I still need to get a suitable set of hinges for the locker tops.

The photos on this thread are not visible unfortunately, so I’d appreciate any photos anyone might have or any specification for hinges or supplier details please.

Thanks

Paul.
Post Reply